Comparison of Mechanical Forces used in Open Tracheotomy versus Percutaneous Tracheotomy Techniques.

OBJECTIVE: To understand the etiology of tracheotomy-induced tracheal stenosis by comparing the differences in techniques and mechanical force applied with open tracheotomy (OT) versus percutaneous tracheotomy (PCT) placement. METHODS: This study is an unblinded, experimental, randomized controlled study in an ex-vivo animal model. Simulated tracheostomies were performed on 10 porcine tracheas, 5 via a tracheal window technique (OT) and 5 using the Ciaglia technique (PCT). The applied weight during the simulated tracheostomy and the compression of the trachea were recorded at set times during the procedure. The applied weight during tracheostomy was used to calculate the tissue force in Newtons. Tracheal compression was measured by anterior-posterior distance compression and as percent change. RESULTS: Average forces for scalpel (OT) versus trocar (PCT) were 2.6 N and 12.5 N (p < 0.01), with the dilator (PCT) it was 22.02 N (p < 0.01). The tracheostomy placement with OT required an average force of 10.7 N versus 23.2 N (p < 0.01) with PCT. The average change in AP distance when using the scalpel versus trocar was 21%, and 44% (p < 0.01), with the dilator it was 75% (p < 0.01). The trach placement with OT versus PCT had an average AP distance change of 51% and 83% respectively (p < 0.01). CONCLUSION: This study demonstrated that PCT required more force and caused more tracheal lumen compression when compared to the OT technique. Based on the increased force required for PCT, we suspect there could also be an increased risk for tracheal cartilage trauma. LEVEL OF EVIDENCE: NA Laryngoscope, 134:103-107, 2024.

Design, development, and face validation of an intubation simulation device using real-time force data feedback.

Objectives: To develop a novel laryngoscope device capable of dynamically measuring force and torque measurements in real-time during intubation and to explore the efficacy of such a device through a face validation simulation. Methods: The torque sensor laryngoscope is designed for use during intubation and is modeled after a standard, single-use plastic laryngoscope. After device calibration, a face validation study was performed with intubation experts in the field. Quantitative data (intubation force metrics) and qualitative data (expert feedback on the device) were collected from three intubations using a Mac blade and three intubations with the Miller blade. Results: Three experts (two anesthesiologists and one otolaryngologist) participated in the study. The mean maximum force exerted with the Mac blade was 24.5 N (95% confidence interval [CI], 22.3-26.8). The average force exerted was 13.6 N (95% CI, 11.7-15.5). The average total suspension time was 13.1 s (95% CI, 10.4-15.8). The average total impulse was 164.6 N·s (95% CI, 147.9-181.4). The mean maximum force exerted with the Miller blade was 31.6 N (95% CI, 26.4-36.8). The average force exerted was 15.8 N (95% CI, 13.8-17.9). The average total suspension time was 11.3 s (95% CI, 9.9-12.6). The average total impulse was 216.2 N·s (95% CI, 186.5-245.9). The mean maximum force (p = .0265) and total impulse (p = .009) were significantly higher in the Miller blade trials than in the Mac blade trials. Survey results found that this device, while bulky, intubated similarly to standard-use models and has potential as an intubation teaching tool. Conclusion: The torque sensor laryngoscope can measure and display real-time intubation force metrics for multiple laryngoscope blades. Initial validation studies showed a significantly lower maximum force and total impulse when intubating with the Mac blade than with the Miller blade. Face validation survey results were positive and suggested the potential for this device as a teaching tool. Level of Evidence: Level 5.